If the product is clogged with foreign objects, the power will be turned off automatically to protect the product. If you clean and maintain your vacuum properly you will continue to enjoy great cleaning performance from your LG cord Zero a 9 stick vacuum. If none of these solutions correct the issue with your LG cord zero A 9 stick vacuum, please contact customer service. Examples of these conditions include: you vacuum everyday, you have pets in the home, you have wall-to-wall carpeting, or you wear shoes in the home. Under certain conditions you may need to clean the filter more often. To maintain cleaning performance, clean the filters at least once a month or as needed. Operating the product with wet filters or without the filters will allow dust to reach the motor and could cost it to malfunction. Insert the crevice tool into the large dust separator and turn it clockwise to lock it in place and reinsert the battery. Reinsert the large dust separator filter into the motor housing. Also keep your fingers or sharp objects out of the motor enclosure to avoid product damage, personal injury, or electric shock. Do not use any wet towels or spray water or cleaner in this area. Before reassembling the filters, you may also want to brush off any dust around the motor housing using the brush attachment. Reinstalling the filters before they are completely dry may result in mildew or odor. After washing the filters allow them to thoroughly dry for at least 24 hours before reinstalling them. Clean off fine debris with a small brush and the large dust separator can be rinsed in any direction. Shake off any large debris from the dust separator over a trash can. To clean the large dust separator filter, enter the crevice tool into the large dust separator and turn it counterclockwise to remove it. The floor or carpet nozzles follow the same steps in reverse. With the nozzle in hand check both ends for debris or obstructions and remove them to reassemble. Clean off fine debris with a small brush. Shake off large debris over a waste basket or trash can.Ĭheck the roller brush for any tangles or obstructions and remove them. Rotate the same panel 90 degrees and pull it outward to remove the roller brush. Use a coin and turn it counterclockwise to unlock it. A round locking mechanism attached to the nozzle side panel is shown. Now move to the body of the unit, check the inlet for any debris or obstructions and remove them to remove debris or obstructions from the floor or carpet nozzle inlets. Look through both ends of the wand and check for any debris or obstructions and remove them. To check the unit for clogs, detach the carpet floor nozzle and the one from the vacuum. Reassemble the pre-filter first, then align the exhaust filter with the hollow indicator at top and turn the filter clockwise until the solid white indicators align. After washing the filters, allow them to thoroughly dry for at least 24 hours before reinstalling them. In order to effectively dislodge the dust from each filter, direct the water flow as shown: Exhaust filter outside-in top to bottom. Directing the air from the inside outward compacts the dust and debris into the filter this increases airflow restriction or clogs and reduces the filters performance even further. When using compressed air on the exhaust filter, make sure to direct the air as shown from the outside in top-to-bottom. Shake off any large debris from the filters, clean off fine debris with a small brush over a trash can, or go outside and use a can of compressed air. The green pre-filter can be accessed once the lid is removed. The exhaust filter is built into the twist off lid. To clean the exhaust filter and pre-filter twist open the top lid on the back and body. Before you perform any maintenance, turn the vacuum off, empty the dust bin over a waste basket or trash can and remove the battery. Interpreting power issues, cycling noise, and loss of suction are indicators that the unit is in need of maintenance. It could also be due to an obstruction in the inlet hose attachment, floor nozzle inlet, or finally it could also be due to the large dust separator filter being packed with dirt and debris. If you're experiencing cleaning performance issues from your LG Cord Zero A 9 stick vacuum due to intermittent power or cycling noise, it may be due to the exhaust filter and green pre-filter being packed with dirt and debris.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |